KLB-SYSTEM EPOXY EP 202
Low-emission 2-Component-Epoxy-Resin-Coating, AgBB-tested with the appropriate accreditation, suitable for an “industrial” recreation room.
The high-quality, free-flow coating KLBSYSTEM
EPOXY EP 202 is based on a lowemission and solvent-free 2-Component-
Epoxy-Resin which features very low VOC*- values. Suitable for many areas like private domains, commercially or industrially used areas with a medium to high load. The 3-layer
system offers a smooth surface due to its free flow and planing characteristics.
The floor is very easy to clean and extremely hygienic. The surface can be produced very fast and economical with KLB-SYSTEM EPOXY EP 202 which is also very beneficial for reconstruction. The free-flow coating is available in a great variety and different colours depending on the design and demand. By applying subsequent coatings or adding quartz sand adequate anti-slip grades can be achieved. The cured coating offers resistance to multiple chemicals.
Application Area:
– Especially for residential properties,
recreation- and adjoining rooms where
people remain, e. g. offices, conferenceand
training classrooms, nurseries, schools,
cafeteria, restaurants, show rooms as well
as private residential and recreation areas
– But also for emission-free commercially and
industrially used areas, e. g. production,
laboratories, stock- and consignment areas
Build-up of System
Layer in Detail
Lamination strength 2 – 3 mm
Coating KLB-SYSTEM EPOXY EP 202
Scratch Coat KLB-SYSTEM EPOXY EP 55 blended with KLB-Sand Blend 2/1
Base Coat KLB-SYSTEM EPOXY EP 55
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Decorative Scattering Adding partiColor®-Chips and subsequently sealing is suitable for the coloured design.
Apply a matt sealer finish.
Increasing the To slightly increase the slip resistance grade scatter with silicum carbide or a delustering
Slip-Resistance Grade agent or seal with the RHX-additive.
Matting A matt surface can be achieved by additionally sealing with KLB-SYSTEM EPOXY
EP 705 E / EP 706 E or KLB-SYSTEM POLYURETHANE PU 805 E / 806 E.
Alternative Coatings Standard: KLB-SYSTEM EPOXY EP 213 or EP 220
Elastic: KLB-SYSTEM POLYURETHANE PU 410 or PU 420
Low-emission coatings can be produced as follows:
and so on
KLB-SYSTEM POLYURETHANE PU 410
High-quality, uv-stable 2-Component-Polyurethane-Coating for decorative living and recreation rooms.
KLB-SYSTEM POLYURETHANE PU 410 is a high-quality, free-flow coating, based on a liquid 2-Component-Polyurethane-Resin. KLBSYSTEM POLYURETHANE PU 410 is suitable for flexible coatings, predominantly for interior areas with impact sound insulation and decorative features. On the contraire to known polyurethane industrial coatings KLB-SYSTEM POLYURETHANE PU 410 is made from uv-stable raw materials and is colour-stable. The coating has good free-flow and smoothing properties and cures with almost no shrinkage. The cured coating shows good flexibility and is crack bridging starting at layers of 2 mm. KLB-SYSTEM POLYURETHANE PU 410 is suitable for interior areas requiring more flexibility due to the substrate.
Increased comfort can be achieved by incorporating a bedding layer. KLB-SYSTEM POLYURETHANE PU 410 can be produced in 14 standard colours, even in pale special colours.
The coating is very suitable for partiColor®-Chips scattering.
Use always in combination with KLBSYSTEM POLYURETHANE PU 805 E – matt and low-emission sealer.
Application Area:
– Especially for decorative living-, recreationand
adjoining rooms, like e. g. show-rooms,
sales-room, offices, hospitals, conferenceand
training classrooms, nurseries, schools
and many more
– Also suitable for exterior areas – please contact
our technical department!
Build-up of System
Layer in Detail
Lamination strength 1 – 2.5 mm
Sealer KLB-SYSTEM POLYURETHANE PU 805 E
Coating KLB-SYSTEM POLYURETHANE PU 410
Scratch Coat KLB-SYSTEM EPOXY EP 55 blended with KLB-Sand Blend 2/1
Base Coat KLB-SYSTEM EPOXY EP 55
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Decorative Scattering Adding partiColor®-Chips and subsequently sealing is suitable for the coloured design.
Apply a matt sealer finish.
Increasing the To slightly increase the slip resistance grade scatter with silicum carbide or a delustering
Slip-Resistance Grade agent or seal with the RHX-additive.
Matting A matt surface can be achieved by additionally sealing with KLB-SYSTEM EPOXY
EP 705 E / EP 706 E or KLB-SYSTEM POLYURETHANE PU 805 E / 806 E.
Alternative Coatings Not colour-stable: KLB-SYSTEM POLYURETHANE PU 420 or PU 421
KLB-SYSTEM EPOXY EP 216 All-Purpose
2-Component-Epoxy-Resin-Coating and Top Sealer in one system tested according to OS 8.
KLB-SYSTEM EPOXY EP 216 All-Purpose is a solvent-free, pigmented 2-Component-Epoxy-Resin-Coating for hard industrial floor covering. KLB-SYSTEM EPOXY EP 216 All-Purpose is high-quality adjusted with excellent covering power. Due to its low viscosity the product is suitable for rolled coatings as well as a top sealer for scattered, slip resistant coatings. The material is suitable for smooth coatings for layers 1 – 4 mm. The coating material has good processing-, free-flow- and planing properties. KLB-SYSTEM EPOXY EP 216 All-Purpose has well balanced properties and may be used all-purpose. Stockage may be reduced because the product is multi-purpose and has a wide range of application possibilities. The coating is very resistant to mechanical load and different chemicals.
Application Area :
– High-quality coating for all commercially and industrially used areas like production areas, assembly halls, stockage rooms, repair shops etc. – Tested according to OS 8 for slip resistant coatings for interior areas, garages and so on.
Build-up of System
Layer in Detail
Smooth Coating OS 8-Coating (slip-resistant)
Lamination strength 1 – 4 mm 2 – 4 mm
Coating KLB-SYSTEM EPOXY EP 216 All-Purpose KLB-SYSTEM EPOXY EP 216 All-Purpose
as top sealer
Primary Layer KLB-SYSTEM EPOXY EP 216 All-Purpose
scattered with quartz sand 0.3/0.8 mm
Scratch Coat KLB-SYSTEM EPOXY EP 50 Optional for increased depth of roughness
blended with KLB-Sand Blend 2/1
Base Coat KLB-SYSTEM EPOXY EP 50 KLB-SYSTEM EPOXY EP 50
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Decorative Scattering Adding partiColor®-Chips and subsequently sealing is suitable for the coloured design.
Apply a matt sealer finish.
Increasing the To slightly increase the slip resistance grade scatter with silicum carbide or a delustering
Slip-Resistance Grade agent or seal with the RHX-additive added.
Matting A matt surface can be achieved by additionally sealing with KLB-SYSTEM EPOXY
EP 705 E / EP 706 E or KLB-SYSTEM POLYURETHANE PU 805 E / 806 E.
Alternative Coatings Standard: KLB-SYSTEM EPOXY EP 213 or EP 220
Low-emission: KLB-SYSTEM EPOXY EP 202
Elastic: KLB-SYSTEM POLYURETHANE PU 420 or PU 421
UV-stable: KLB-SYSTEM POLYURETHANE PU 410
KLB-SYSTEM EPOXY EP 175 Special
UV-stable, scattered with coloured sand and decorative coating for wet areas.
For a joint-less, scattered coating the demand to slip resistance and hygiene are most important. The coating consists of several layers: Base Coat, Primary Coat, Scattered Coat with coloured and special Sand as well as two transparent Sealing Coats with KLB-SYSTEM EPOXY EP 175 Special and a chemical resistant Matt Sealer KLB-SYSTEM EPOXY EP 860. KLB-SYSTEM EPOXY EP 175 Special is a high-quality, solvent-free 2-Component- Epoxy-Resin for a transparent seal of decorative scattered coatings and decorative mortar coatings. The flooring shows an even appealing appearance. Usage in areas with demands to increased mechanical load and chemical resistance is possible because the material is epoxy resin based. The surface slip resistant can be adjusted according to the requirements of BGR 181. The coating is hygienic, very well cleanable and resistant to water and many chemicals. With increased exposure to hot water and other “hot” medias we recommend KLBSYSTEME PU-CONCRETE.
Application Area:
– Kitchen
– Butcheries, abattoirs
– Fish- and food-industry
– Beverage industry, vinification industry and
other areas with exposure to water
Build-up of System
Layer in Detail
Anti-Slip Grade according to BGR 181 R11 – V4 R12 – V6
Lamination strength 3 – 5 mm 4 – 6 mm
Sealer Chemical resistant KLB-SYSTEM EPOXY EP 860
Top Sealer KLB-SYSTEM EPOXY EP 175 Special,
Consumption depending on the slip-resistance grade
Scattering Coloured Sand Blend, grain size Coloured Sand Blend, grain size
0,3/0,8 mm 0,7/1,2 mm
Primary Layer KLB-SYSTEM EPOXY EP 216 All-purpose,
alternative: EP 213 or EP 99
Scratch Coat KLB-SYSTEM EPOXY EP 50 Optional for increased
blended with KLB-Sand Blend 2/1 depth of roughness
Base Coat KLB-SYSTEM EPOXY EP 50,
alternative: EP 30 or EP 52 Special depending on the substrate requirements
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coats instructions or advice by our technicians.
Possibilities in colours
A wide variety in colours is possible due to coloured sand scattering. Light pale-coloured mixtures are beneficial. A small ratio of
dark grain is recommended.
KLB-SYSTEM EPOXY EP 785 HS
Low-emission, vapour-permeable 2-C-Epoxy-Resin-Free-Flow-Coating.
KLB-SYSTEM EPOXY EP 785 HS is a solventfree, pigmented flow-coating based on a water-emulsified 2-Component-Epoxy-Resin- System with very good free-flow and planing properties. The special advantage of this system relies on the composition which results in a vapour-permeable film. The constituent parts are all adjusted vapourpermeable. It is especially suitable for reconstruction of magnesia-screed, sensitive to humidity as well as for soil-contacting substrate without adequate sealing. KLB-SYSTEM EPOXY EP 785 HS results in a smooth, fine non-slip, very appealing, matt surface. The coating is suitable for commercially and industrially used areas with medium load. Usage in wet areas is not recommended.
Application Area:
– Commercially and industrially used areas
with a light to medium load
– Mainly for dry areas
– Reconstruction of magnesia coatings
– For substrate with ascending humidity
– For new buildings with increased humidity
in the substrate
Build-up of System
Layer in Detail
Smooth Coating Scattered (slip-resistant) R11
Lamination strength 1.5 – 2.5 mm 2 – 4 mm
Sealer KLB-SYSTEM EPOXY EP 740 E, alternative: 1. Layer: KLB-SYSTEM EPOXY EP 785 HS
EP 701 E or PS 88 Maintenance Sealer 2. Layer: KLB-SYSTEM EPOXY EP 740 E
Coating KLB-SYSTEM EPOXY EP 785 HS
Primary Layer KLB-SYSTEM EPOXY EP 785 HS
and Scattering primary layer completely scattered
with quartz sand 0.3/0.8 mm
Scratch Coat KLB-SYSTEM EPOXY EP 782 E Optional for increased depth of roughness
Filling Primer
Base Coat KLB-SYSTEM EPOXY EP 727 E KLB-SYSTEM EPOXY EP 727 E
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Decorative Scattering Adding partiColor®-Chips and subsequently sealing is suitable for the coloured design.
Apply a matt sealer finish.
Increasing the To slightly increase the slip resistance grade seal with the RHX-additive added.
Slip-Resistance Grade
Glossy Maintenance KLB-SYSTEM Industrial Floor Maintenance PS 88
Matting KLB-SYSTEM EPOXY EP 705 E / EP 706 E
Alternative Coatings Economic: Apply KLB-SYSTEM EPOXY EP 740 E twice
Electrically conductive: KLB-SYSTEM EPOXY EP 785 EL+
Commercially and industrially used coatings can be produced as follows:
KLB-SYSTEM EPOXY EP 211 ESD
Homogeneous conductive 2-C-Epoxy-Resin-Coating for increased requirements to ESD-areas and transition resistance.
KLB-SYSTEM EPOXY EP 211 ESD is an electrically conductive, coloured coating based on a 2-Component-Epoxy-Resin for industrial areas. Beside its good attributes of a joint-less and abrasion resistant epoxy resin coating, the coating is electrically conductive. It is especially suitable for the increased demands to ESD-protection. Especially suitable for assembly- and testing-rooms, manufacturing, testing or handling electrical parts. KLB-SYSTEM EPOXY EP 211 ESD provides the latest adjusted conductive technology. The material is conductive, to a large extent independent of thickness of layers and can be provided in pale colours. KLB-SYSTEM EPOXY EP 211 ESD provides a very good resistance to mechanical load and to chemicals. It is stable to oil, grease, water, salt-solutions and different acids and bases. KLB-SYSTEM EPOXY EP 211 ESD is suitable for slip resistant, scattered coatings.
Application Area:
– For all areas of electronics and electrical
engineering with requirements to ESD like
e. g. test rooms, laboratories, assembly
halls, stockage areas and many more
Build-up of System
Layer in Detail
Smooth Coating Smooth Coating
Lamination strength 1.5 – 2.5 mm 1 – 2 mm
Coating Standard: High-Quality:
KLB-SYSTEM EPOXY EP 211 ESD KLB-SYSTEM EPOXY EP 212 ESD
Conductive Coat Install grounding system with copper bands on 1 – 2 spots for each 100 m².
and Grounding Apply the conductive coat KLB-SYSTEM EPOXY EP 799 Conductive Coat
Scratch Coat KLB-SYSTEM EPOXY EP 50 mixed with KLB-Sand Blend 2/1
Base Coat KLB-SYSTEM EPOXY EP 50
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Increasing the To slightly increase the slip resistance grade scatter with silicum carbide.
Slip-Resistance Grade
Matting For a matt surface additionally apply KLB-SYSTEM POLYURETHANE PU 881 EL+ .
Alternative Coatings Standard: KLB-SYSTEM EPOXY EP 200 EL+
For ESD-requirements: KLB-SYSTEM EPOXY EP 211 ESD, EP 212 ESD or EP 200 EL+
combined with PU 881 EL+
Elastic: KLB-SYSTEM POLYURETHANE PU 413 EL+
Vapour-permeable: KLB-SYSTEM EPOXY EP 785 EL+ or EP 790 EL+
For WHG-requirements: KLB-SYSTEM EPOXY EP 280 WHG
Resistant to Chemicals: KLB-SYSTEM EPOXY EP 285 EL+
Commercially and industrially used coatings can be produced as follows:
KLB-SYSTEM EPOXY EP 785 EL+
Electrically conductive, vapour-permeable 2-C-Epoxy-Resin-Free- Flow-Coating.
KLB-SYSTEM EPOXY EP 785 EL+ is a solvent- free, pigmented free-flow coating based on a water emulsified 2-Component- Epoxy-Resin-System with very good free-flow and planing properties. The particular advantage of this coating system is the special composition which results in a vapour-permeable coating. The parts are all adjusted steam-permeable and especially suitable for magnesia screed. Also suitable for soil-contacting substrate without sufficient sealing. KLB-SYSTEM EPOXY EP 785 EL+ is adjusted electrically conductive and results in a fine non-slip, very appealing, matt surface. The coating is suitable for commercially and industrially used areas with medium. mechanical load with requirements to conductivity. Not recommended for wet areas.
Application Area:
– Commercially and industrially used coatings
with demands to the electrical conductivity
with light to medium load
– Mainly for dry interior areas
– Reconstruction of magnesia coatings
– For substrate with ascending humidity
– For new coatings with increased humidity
Build-up of System
Layer in Detail
Smooth Coating
Lamination Strength 1.5 – 2.5 mm
Sealer KLB-SYSTEM EPOXY EP 790 EL+ and Maintenance PS 90
Coating KLB-SYSTEM EPOXY EP 785 EL+
Conductive Coat Install grounding system with copper bands on 1 – 2 spots for each 100 m².
and Grounding Apply the conductive coat KLB-SYSTEM EPOXID EP 799 Conductive Coat
Scratch Coat KLB-SYSTEM EPOXY EP 782 E Filling Primer
Base Coat KLB-SYSTEM EPOXY EP 727 E
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Increasing the To slightly increase the slip resistance grade scatter with silicum carbide.
Slip-Resistance Grade
Alternative Coatings Steam Tight: KLB-SYSTEM EPOXY EP 200 EL+, EP 211 ESD or EP 212 ESD
Elastic: KLB-SYSTEM POLYURETHANE PU 413 EL+
For WHG-requirements: KLB-SYSTEM EPOXY EP 280 WHG
Resistant to Chemicals: KLB-SYSTEM EPOXY EP 285 EL+
Commercially and industrially used coatings can be produced as follows:
Seek advice for requirements to explosion protection!
KLB-SYSTEM EPOXY EP 236
The economical 2-C-Epoxy-Resin-Textured-Coating
KLB-SYSTEM EPOXY EP 236 is a coloured, thixotropic adjusted 2-Component-Epoxy- Resin-Coating for thin, burling-textured coating. Due to its consistency the surface structure can be achieved easily. KLB-SYSTEM EPOXY EP 236 results in optically
appealing floor- and wall-coatings with a textured, glossy and free-of-pores surface. The coating is abrasion resistant and resistant to light mechanical load. By adding 10 – 15 % of silicum carbide abrasion resistance and slip-resistance can be increased. The coating offers good resistance to chemicals, especially to aqueous salt solutions, acids and bases, as well as oil and benzene. Conditionally resistant to diluted organic acids. KLB-SYSTEM EPOXY EP 236 offers a good colour tone stability.
Application Area:
– Floor- and wall-coating for all commercially
and industrially used areas like production
rooms, assembly halls and stockage rooms,
repair shops and many other rooms
Build-up of System
Layer in Detail
Lamination Strength 0.5 – 1.0 mm
Textured Coating KLB-SYSTEM EPOXY EP 236
Scratch Coat (Optional) KLB-SYSTEM EPOXY EP 50 blended with KLB-Sand Blend 2/1
Base Coat KLB-SYSTEM EPOXY EP 50
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Decorative Scattering Adding partiColor®-Chips (size 1 mm) and subsequently sealing is suitable for
the coloured design. Apply a matt sealer finish.
Increasing the To increase the slip resistance grade add 10 – 15 % silicum carbide.
Slip-Resistance Grade
Matting For a matt surface additionally apply KLB-SYSTEM EPOXY EP 705 E / EP 706 E.
Alternative Coatings Standard: KLB-SYSTEM EPOXY EP 213 or EP 220
Elastic: KLB-SYSTEM POLYURETHANE PU 420 or PU 421
Thin-coated, conductive: KLB-SYSTEM EPOXY EP 233 EL+
Steam-permeable: KLB-SYSTEM EPOXY EP 740 E
Commercially and industrially used coatings can be produced as follows
KLB-SYSTEM EPOXY EP 740 E
Pigmented, low-emission 2-C-Epoxy-Resin-Sealer
KLB-SYSTEM EPOXY EP 740 E is a 2-Component, water-emulsified, pigmented Epoxy- Resin-Sealer for thin coatings. KLB-SYSTEM EPOXY EP 740 E is mainly used as a sealer on concrete, cement screed, magnesia and mastic asphalt, as well as for reconstructing already existing surfaces. The material is easy to apply with a roller and is pleasant to work with and environmentally friendly due to its consistency. Applied in 2 – 3 layers a durable and optically appealing floor sealer is achieved. The material cures by drying and chemically cross-linking to a sturdy and robust film with good adhesion. KLB-SYSTEM EPOXY EP 740 E is adjusted with low emission and results in a energy-elastic, almost abrasion resistant film. Physiologically harmless with good resistance to aqueous solutions, diluted acids and bases as well as to engine and fuel oil. The vapour-permeability allows sealing of which is sensitive to water and increased dampness substrate. Very good economic results can be achieved by combining KLB-SYSTEM EPOXY EP 740 with KLB-SYSTEM EPOXY EP 727 E which offers good adhesion on different, even old substrates.
Application Area:
– All surfaces with light load, e. g. pedestrians
and light traffic, for interior and exterior
areas
– Especially for recreational rooms and side
rooms, where people remain
– But also for commercially and industrially
used areas like e. g. production areas,
laboratories, stockage areas and so on
– Secondary rooms for technical equipment,
basements, storage rooms and so on
Build-up of System
Layer in Detail
Lamination Strength 0.5 – 1.0 mm
Sealer Apply KLB-SYSTEM EPOXY EP 740 E twice
Scratch Coat (Optional) KLB-SYSTEM EPOXY EP 50 blended with KLB-Sand Blend 2/1,
alternative: vapour-permeable with EP 782 E Filling Primer
Base Coat KLB-SYSTEM EPOXY EP 727 E
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Decorative Scattering Adding partiColor®-Chips (size 1 mm) and subsequently sealing is suitable for the
coloured design. Finally apply a matt sealer finish, e. g. KLB-SYSTEM EPOXY EP 705 E.
Increasing the To slightly increase the slip resistance grade add RHX-additive.
Slip-Resistance Grade
Alternative Coatings Standard: KLB-SYSTEM EPOXY EP 213 or EP 220
Elastic: KLB-SYSTEM POLYURETHANE PU 420 or PU 421
Thin-coated, conductive: KLB-SYSTEM EPOXY EP 233 EL+
Thin-coated, textured: KLB-SYSTEM EPOXY EP 236
Commercially and industrially used coatings can be produced as follows:
KLB-SYSTEM EPOXY EP 172
Decorative Quartz-Pebble-Coatings for interior and exterior areas
Quartz-Pebble-Coatings are decorative coatings combined by natural-, coloured quartz- or marble-granulates and high-quality KLB-binding agents. The novel formulated KLB-SYSTEM EPOXY EP 172 is low in solvents and emission and can be used as binding agent. KLB-SYSTEM EPOXY EP 172 results in a glossy surface and shows only slight yellowing. That’s why it is especially suitable for all decorative and coloured sand coatings. Due to its innovative composition the binding agent fulfills particularly the requirements for recreation rooms according to legal regulations. Accreditation of the German Institute for Construction (DIBt) is at hand. The coatings may be excellently combined with other materials like wood or stainless steel. Corporate symbols and lettering can be integrated without any problems. Offers unique floors with individual design. Decorative-Pebble-Coatings can be used for interior and exterior areas.
Application Area:
– Balconies and patios
– Sales offices
– Show rooms
– Entrance hall
– Living rooms
and many more
Build-up of System
Layer in Detail
Lamination Strength 5 – 10 mm
Top Sealer (Optional) KLB-SYSTEM EPOXY EP 172
Coating Different sized quartz pebbles, usually 2/3 mm, 3/4 mm, or 4/6 mm bound with
with KLB-SYSTEM EPOXY EP 172. Resinate coatings with increased load.
Scratch Coat (Optional) KLB-SYSTEM EPOXY EP 55 blended with KLB-Sand Blend 2/1
Base Coat KLB-SYSTEM EPOXY EP 55, scattered with grain size 1/2 mm
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Interior Coatings Bound with KLB-SYSTEM EPOXY EP 172, alternative: EP 174, EP 175.
Exterior Coatings Bound with KLB-SYSTEM POLYURETHANE PU 9010 or PU 9030, re-sealing may be required.
Commercially and industrially used coatings can be produced as follows:
KLB PRODUCTS
KLB-SYSTEM EPOXY EP 280 WHG and EP 282 WHG
Chemically resistant 2-C-Epoxy-Resin-Coatings with technical approval for water protection
Application Area:
– Coating of collection-rooms and -trays in
regard to the WHG*-requirements and
technical approval
– Industrial flooring with traffic in regard to
the WHG*-requirements
– Electrically conductive and chemically
resistant industrial flooring
Build-up of SystemLayer in Detail
Conductive Coating Non-conductive Coating (Standard)
Lamination strength 2 – 3 mm 2 – 3 mm
Coating KLB-SYSTEM EPOXY EP 280 WHG KLB-SYSTEM EPOXY EP 282 WHG
Conductive Coat Install grounding system with copper bands on 1 – 2 spots for each 100 m².
and Grounding Apply the conductive coat KLB-SYSTEM EPOXY EP 799 Conductive Coat.
Scratch Coat KLB-SYSTEM EPOXY EP 55 KLB-SYSTEM EPOXY EP 55
mixed with KLB-Sand Blend 2/1 mixed with KLB-Sand Blend 2/1
Base Coat KLB-SYSTEM EPOXY EP 55 KLB-SYSTEM EPOXY EP 55
Substrate Requirements to the substrate according to the BEB-worksheets
and our detailed base coat instructions or advice by our technicians.
System Variant
Layer in Detail
Increasing the To slightly increase the slip resistance grade scatter with silicum carbide.
Slip-Resistance Grade
Matting For a matt surface additionally apply KLB-SYSTEM POLYURETHANE PU 881 EL+.
Alternative Coatings Conductive:
Standard: KLB-SYSTEM EPOXY EP 200 EL+
For ESD-requirements: KLB-SYSTEM EPOXY EP 211 ESD, EP 212 ESD or EP 200 EL+
combined with PU 881 EL+
Elastic: KLB-SYSTEM POLYURETHANE PU 413 EL+
Steam-permeable: KLB-SYSTEM EPOXY EP 785 EL+ or EP 790 EL+
Commercially and industrially used coatings can be produced as follows
KLB-SYSTEM PU-CONCRETE
Industrial flooring for wet areas – resistant to hot water and chemicals
Application Area:
– Breweries, vinification industry,
beverage industry
– Slaughterhouses and butcheries
– Food industry, backeries
– Creamery / dairy farming
– Chemical industry, pharmaceutical industry
and many more
Build-up of System
Layer in Detail
R10 R12 (slip-resistant)
Lamination Strength 8 – 10 mm 8 – 10 mm
Top Coat KLB-SYSTEM PU-CONCRETE 4010 Grip KLB-SYSTEM PU-CONCRETE 4080
as Top Sealer
Prime Coat KLB-SYSTEM PU-CONCRETE 4009
and Scattering scattered with Corundum 0.5/1.0 mm
Scratch Coat Optional for increased depth of roughness with KLB-SYSTEM PU-CONCRETE 4006
Base Coat KLB-SYSTEM PU-CONCRETE 4050 Base Coat
Substrate Requirements to the substrate according to the BEB-worksheets and our detailed base coat
instructions or advice by our technicians. Important: watch for tensile strength and compression
proof substrate as well as anchoring cuts according to the requirements.
System Variant
Layer in Detail
Slip Resistance Class R9 – R13 can be achieved by scattering with sand or corundum.
Colour 4 different colours are available
Alternative Coatings For layers 6 mm: KLB-SYSTEM PU-CONCRETE 4006
Conductive adjustment: KLB-SYSTEM PU-CONCRETE 4006 EL+
